Brother DCP-110C Service Manual Download Page 280

Page: 280 / 466

8-22

Confidential

If the sensing status are as listed below, the LCD will show "DFDRCVRS P1 " and

"IKIYICIMVTHKLK ," which can be switched by pressing the

Black Start (Mono Start)

key.

Given below is the relationship between the LCD indication, sensor name and sensor status.

LCD

Sensors

Sensing status

DF Document front sensor*

No document detected.

DR Document rear sensor*

No document detected.

CV Scanner open sensor

Scanner unit closed.

Registration sensor

No recording paper detected.

Purge cam switch

Purge cam switch ON.

Black ink cartridge sensor

Black ink cartridge loaded (Black ink present).

Yellow ink cartridge sensor

Yellow ink cartridge loaded (Yellow ink present).

Cyan ink cartridge sensor

Cyan ink cartridge loaded (Cyan ink present).

Magenta ink cartridge sensor

Magenta ink cartridge loaded (Magenta ink present).

VT Head driver chip temperature sensor

Driver chip temperature within the allowable range.

HK Hook switch**

On-hook state.

LK Large-volume ink cartridge sensor*** Large volume ink cartridge loaded.

* MFC620CN/425CN/420CN/DCP120C and FAX2440C

** MFC620CN/620CN New U.S.A./Canadian models and

FAX2440C

***

FAX2440C

The DF, DR, HK, and LK are displayed even on those models not equipped with their related

sensors.

(2) Change the detecting conditions (e.g., open the scanner unit or insert paper through the

registration sensor or remove the ink cartridges), and then check that the indication on the

LCD changes according to the sensor states.

(3) To stop this operation and return the machine to the initial stage of the maintenance mode,

press the

Stop/Exit

key.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands