manualshive.com logo in svg

Brother DCP-110C, Service Manual

Share
Download
Brother DCP-110C Service Manual Download Page 143

 5-5 

Confidential

 

5.1.1  Draining the Ink from the Ink Tubes 

-- Be sure to perform draining before removing the head/carriage unit, ink refill ASSY or engine unit. -- 

(1)  Open the scanner cover (scanner unit) and pull out all four ink cartridges. 
(2)  As shown below, attach a piece of black vinyl adhesive tape to each of four dummy cartridges 

to prevent the ink cartridge sensors from detecting ink near-empty. 

 

Then load those dummy cartridges into the cartridge slots and close the scanner cover. 

 

Dummy 

cartridges

Scanner cover 

(Scanner unit)

Ink cartridges

Attach a piece of 

black adhesive tape.

 

 

 

(3)  Plug the power cord into an electrical outlet. 

MFC620CN/245CN/420CN/410CN/215C/210C and FAX2440C 

(4) Press the 

Menu/Set

 and 

Black

 

Start 

keys. Next press the   key four times to make the 

machine enter the maintenance mode. 

 The 

"

" appears on the LCD.

 

 

TIP:

  FAX models equipped with numerical keypads can enter the maintenance mode in the 

same way as conventional models; that is, by pressing the 

Menu/Set

, 

*

, 

2

, 

8

, 

6

 and 

4

 keys in 

this sequence. 

(5)  Carry out "Initial purge" (with Function code 76) by pressing the 

7

, 

6

, 

4

 and 

Black

 

Start

 keys. 

 

For details, refer to 

Chapter 8, Section 8.5.20 "Purging Operation."

 

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands