manualshive.com logo in svg

Brother DCP-110C, Service Manual

Share
Download
Brother DCP-110C Service Manual Download Page 171

 5-33 

Confidential

 

Removing the head/carriage unit and CR timing belt 

NOTE:

 During the removal or installation job for the head/carriage unit, take care not to 

contaminate the CR encoder strip or PF encoder disk with grease applied to the head/carriage unit. 

NOTE:

 Do not disassemble the old type of the head/carriage unit. Always handle it together with 

the carriage PCB and head flat cables. 

(8)  While pressing the idle pulley to the right, remove the CR timing belt from the carriage motor 

pulley and idle pulley. 

(9)  Move the head/carriage unit to the left end of its travel. 

(10) Align the bosses on the head/carriage unit with the cutouts in the engine unit and lift the 

head/carriage unit up and off the engine unit.  

 

NOTE:

 Do not touch the print nozzles (the printing ends) or ink supply ports (to which ink 

supply tubes are connected) of the head/carriage unit; doing so will not only stain your hands 

with ink but also damage the nozzles and supply ports. If you do touch them though, clean 

them with a special-purpose cleaning stick and liquid.  

(11)  Remove the CR timing belt from the head/carriage unit. 

 

 

 

 

  

 

 

  

  

  

 

 

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands