manualshive.com logo in svg

Brother DCP-110C, Service Manual

Share
Download
Brother DCP-110C Service Manual Download Page 111

 3-23 

Confidential

 

Air flow path

Ink flow path

 

 

Ink refill assembly components and their main roles 
-  Ink refill base 

  This holds the ink cartridges and feeds ink from them to the ink supply tubes. 
-  Cartridge clamp springs 

  These force the ink cartridges into close contact with the ink cartridge joint to prevent ink 

leakage. 

- Joint head 

  This lifts the disc valves S and D, allowing ink to flow out of the ink cartridges and air to flow in. 

It also incorporates measures to prevent insertion of the wrong ink cartridges. 

-  Ink cartridge sensors 

  These detect when the ink cartridges are running out of ink ("Ink near-empty"). 
- Polyurethane foam 

  This absorbs any ink that leaks from the ink cartridges, limiting its spread and thus reducing the 

risk of damage to other components. 

 
Ink refill assembly 
The cartridge clamp springs force the ink cartridge ink supply ports into close contact with the joint 

head to prevent ink leakage. 
The ink from the ink cartridges flows along paths in the ink refill base and through connectors into 

the ink supply tubes. As the ink level in an ink cartridge drops, the pressure inside falls, drawing in 

air from the air supply port in the ink refill base. 
Polyurethane foam absorbs any ink that leaks from the ink cartridges, limiting its spread and thus 

reducing the risk of damage to other components. 
An ink cartridge sensor arm blocking light to a cartridge sensor indicates that there is ink in the ink 

cartridge. When ink runs low, the arm moves out of the beam, activating the sensor. (Note that the 

firmware also interprets a missing ink cartridge as running low on ink.) 

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands