manualshive.com logo in svg

Brother DCP-110C, Service Manual

Share
Download
Brother DCP-110C Service Manual Download Page 229

 6-7 

Confidential

 

6.2  IF YOU REPLACE THE HEAD/CARRIAGE UNIT 

OR ENGINE UNIT 

[ 1 ]  Load the full maintenance program temporarily (Required for the MFC210C U.S.A./Canadian 

models) 

NOTE:

 Before proceeding the program loading procedure, install the printer driver to the work PC. 

(Refer to

 Appendix 2.

) 

NOTE:

 The full maintenance program file (LZ****.

 upd

) should be saved in an arbitrary folder in 

the work PC beforehand. 
(1)  Make sure that the machine's power cord is unplugged from an electrical outlet. 
 

If the machine is connected to a PC, unplug the USB cable. 

(2)  Switch on the work PC. 
(3)  While holding down the 

5

 key, plug the machine's power cord into an electrical outlet. 

NOTE:

 This step is not required if the main PCB is replaced with a new one. Just turning on 

the machine automatically switches to program loading. 

(4)  Connect the machine to the work PC using the USB cable. 
(5)  Run "FILEDG32.exe" in the folder created. 
 

The Filedrgs window appears as shown below. 

 

 

(6)  Drag and drop the full maintenance program icon onto the BHL2-Maintenance Printer icon in 

the Filedrgs window shown above. 

 

When the work PC starts loading the full maintenance program to the flash ROM in the 

machine, the machine beeps intermittently. 

 

Loading terminates in approx. one minute. Before the machine automatically switches to 

standby, disconnect the USB cable. 

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands