Brother DCP-110C Service Manual Download Page 173

Page: 173 / 466

5-35

Confidential

NOTE:

When storing the head/carriage unit for a long period, be sure to put an air buffer cap

on the head/carriage unit and store the unit in the head casing, as shown below. Leaving the

head/carriage unit out of the casing will cause the print nozzles and ink supply ports to dry up,

resulting in a damaged head.

Air buffer cap

Head casing (lower)

Head/carriage unit

Latch

Head casing (upper)

Reassembling Notes

• When replacing the old type of the head/carriage unit with a new type, also replace the current

upper cover and head cover with a new type. For the mounting procedure of the new type of the

head/carriage unit, see

page 5-43.

• When handling the head/carriage unit, put on a grounding wrist band and perform the job on a

static mat. Also take care not to touch the conductor sections on the flat cables.

• When you set a new head/carriage unit to the machine, apply lubricant to the 5 points specified in

Section 5.2.

• After replacement of the head/carriage unit, check that the CR encoder strip and PF encoder disk

are free of grease. If they are stained with grease, replace them.

• If you replace the head/carriage unit, make adjustments specified in

Chapter 6, Section 6.2.

• When mounting the head/carriage unit, route the head flat cables and attach the FFC support film

and FFC sponge, using the following procedure. (See the illustration on the next page.)

1) Attach a piece of double-sided adhesive tape, which is used to secure the head flat cable 1 to

the lower cover, to the position shown on the next page.

2) Attach the CR timing belt to the head/carriage unit, then mount the head/carriage unit to the

engine unit.

3) Make sure that the head joint rubber is set on the head/carriage unit. Then secure the head

joint to the head/carriage unit with the joint leaf spring.

4) Set the head flat cables to section "b" of the cable clamp on the head joint.

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands