Brother DCP-110C Service Manual Download Page 263

Page: 263 / 466

8-5

Confidential

8.4 USER-ACCESS TO THE MAINTENANCE

MODE

Basically, the maintenance-mode functions listed on the previous page should be accessed by

service personnel only. However, you can allow end users to access some of these under the

guidance of service personnel (e.g., by telephone).
The user-accessible functions (codes 10, 11, 12, 53, 66, 75, 76, 80, 82, 87, and 91) are

shaded

the table given on the previous page. Function code 10 accesses the firmware switches, each of

which has eight selectors. You should not allow end users to access all of those selectors, but you

can allow them to access user-accessible selectors which are

shaded

in the firmware switch tables

Appendix 4.

The service personnel should instruct end users to follow the procedure given below.

MFC620CN/425CN/420CN/410CN/215C/210C and FAX2440C

(1) Press the

Menu/Set

Black Start

Menu/Set

, and

Black Start

keys in this order.

TIP:

For the FAX models equipped with numerical keypads, you may press the

Menu/Set

Black Start

, and

keys instead in the same way as conventional models.

The "MAINTENANCE 10" appears on the LCD.

(2) To access function code 10, press the

Menu/Set

key.

To access any other function code, call up the desired code using the and keys or

numerical keys.

Then press the

Menu/Set

key.

For function code 10, access the desired firmware switch according to the operating procedure

described in

Appendix 4

(3) To switch the machine back to the standby state, press the

Stop/Exit

key. When each of the

user-accessible functions is completed, the machine automatically returns to the standby state.

MFC620CN

Black Start

key

Stop/Exit

key

Menu/Set

key

and keys

Summary of Contents for DCP-110C



















































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands

Brother DCP-110C, Service Manual

Search results

Summary of Contents for DCP-110C

Reviews:

Brands by name

Popular brands