3 608 878 300
Tightening Technology |
Bosch Rexroth AG 133
System 350
| 3 608 878 300/2019-03
ES LED Green
ErgoSpin LED Green: Sets the green ErgoSpin LED
This signal is available as of version V2.300 of the
Rexroth Tightening System 350
.
Input signal used for:
•
Tightening channel (
EsLEDGreen
)
•
Communication unit in single-channel operation (
CH x.y EsLEDGreen
)
Using this signal, a superior control can activate the green LED on the hand-held nutrunner from outside.
This signal can only be activated if it has been assigned in the PLC assignment table. Once one of the
EsLEDGreen
,
EsLEDRed
and
EsLEDYellow
signals has been assigned in the PLC assignment table, the
external controller will assume the task of activating the LED. i.e. the present display of
OK
or
NOK
and
enabling by the tightening system will no longer be applicable.
ES LED Red
ErgoSpin LED
Red:
Sets the red ErgoSpin LED
This signal is available as of version V2.300 of the
Rexroth Tightening System 350
.
Input signal used for:
•
Tightening channel (
EsLEDRed
)
•
Communication unit in single-channel operation (
CH x.y EsLEDRed
)
Using this signal, a superior control can activate the red LED on the hand-held nutrunner from outside.
This signal can only be activated if it has been assigned in the PLC assignment table. Once one of the
EsLEDGreen
,
EsLEDRed
and
EsLEDYellow
signals has been assigned in the PLC assignment table, the
external controller will assume the task of activating the LED. i.e. the present display of
OK
or
NOK
and
enabling by the tightening system will no longer be applicable.
ES LED Yellow
ErgoSpin LED
Yellow
: Sets the yellow ErgoSpin LED
This signal is available as of version V2.300 of the
Rexroth Tightening System 350
.
Input signal used for:
•
Tightening channel (
EsLEDYellow
)
•
Communication unit in single-channel operation (
CH x.y EsLEDYellow
)
Using this signal, a superior control can activate the yellow LED on the hand-held nutrunner from outside.
This signal can only be activated if it has been assigned in the PLC assignment table. Once one of the
EsLEDGreen
,
EsLEDRed
and
EsLEDYellow
signals has been assigned in the PLC assignment table, the
external controller will assume the task of activating the LED. i.e. the present display of
OK
or
NOK
and
enabling by the tightening system will no longer be applicable.
GO_SetRef
Set Geared Offset Reference Point: Flat output drive offset position reference point
This signal is available as of version V2.500 of the
Rexroth Tightening System 350
.
Input signal used for:
•
Tightening channel (
GO_SetRef
)
•
Communication unit in single-channel operation (
CH x.y GO_SetRef
)
This signal is only active for tightening channels with ErgoSpin. The signal is only updated outside of the
tightening operation.
This signal is only active for tightening channels with ErgoSpin. The signal is only updated outside of the
tightening operation.
This signal is only active for tightening channels with ErgoSpin. The signal is only updated outside of the
tightening operation.
Summary of Contents for Rexroth Tightening System 350
Page 4: ...4 641 Bosch Rexroth AG Schraubtechnik System 350 3 608 878 300 2019 03 ...
Page 120: ...120 641 Bosch Rexroth AG Tightening Technology 3 608 878 300 System 350 3 608 878 300 2019 03 ...
Page 194: ...194 641 Bosch Rexroth AG Tightening Technology 3 608 878 300 System 350 3 608 878 300 2019 03 ...
Page 638: ...638 641 Bosch Rexroth AG Tightening Technology 3 608 878 300 System 350 3 608 878 300 2019 03 ...
