Bosch LTC 1311/20 FlexiDome I Configuration Manual Download Page 134

Page: 134 / 188

134

en | Cameras and Recording page

Bosch Video Management System

Configuration Client | V3 | 2010.07

Configuration Manual

Bosch Sicherheitssysteme GmbH

Device Family

Displays the type of firmware used in the encoder.

Camera

Displays the name of the camera.

Network Address

Displays the IP address of the camera.

Location

Displays the location of the camera. If the camera is not assigned to a location yet,

Unassigned Location

is displayed.

Live Quality (only VRM and Live / Local Storage)

Click a cell to select the live quality for a

VRM

or a local storage / live only

encoder

of stream 2.

Number

Click a cell to edit the logical number that the camera received automatically when it was

detected. If you enter an already used number, a corresponding error message is displayed.

The logical number is "free" again when the camera is removed.

Audio

Click a cell to assign an audio source to the camera. Only for NVR recording: You can assign

one audio source to multiple cameras.

If an

alarm

occurs with low priority and with a camera that has audio configured, this audio

signal is played even when an alarm with higher priority is currently being displayed. But this

is only true, if the high priority alarm has no audio configured.

(Only visible when you click

All

)

Select a check box to activate PTZ control.

Note:

For port settings refer to

Section 18.12.1 COM1, page 122

Protocol

(Only visible when you click

All

)

Click a cell to select the appropriate protocol for the PTZ control.

Dome Address

(Only visible when you click

All

)

Type the address number for the PTZ control.

Storage

Min Time [days] (only VRM and Local Storage)

Click a cell to edit the minimum number of days that video data from this camera is retained.

Recordings younger than this number of days are not deleted automatically.

Storage

Max Time [days] (only VRM and Local Storage)

Click a cell to edit the maximum number of days that video data from this camera is retained.

Only recordings older than this number of days are deleted automatically.

Summary of Contents for LTC 1311/20 FlexiDome I





























































































































































































Search results

Summary of Contents for LTC 1311/20 FlexiDome I

Reviews:

Related manuals for LTC 1311/20 FlexiDome I

Brands by name

Popular brands

Bosch LTC 1311/20 FlexiDome I, Configuration Manual

Search results

Summary of Contents for LTC 1311/20 FlexiDome I

Reviews:

Related manuals for LTC 1311/20 FlexiDome I

Brands by name

Popular brands