Bosch DDU 7 Manual Download Page 152 | Manualshive

Page: 152 / 156

background image

152

en | Enhancements

Display Unit DDU 7

04.02.2019 | V 02 |

Manual

Bosch Motorsport

3.

The mounting location is now stored in the device. The device will do a reset and the
‘RUN’ led on the device will change to green. The list will show the new mounting location
assignment.

It is good practice to physically label the M 60 with its mounting location.
Now the device is ready to be used.
A different coloring of the M 60 is used to indicate that the device is already configured in
the currently loaded RaceCon project or not (white/orange).
A conflict of several connected M 60 using the same location is indicated by red coloring
the involved devices:

«
...
150
151
152
153
154
...
»

Summary of Contents for DDU 7





























































































































































Reviews:

No comments

Related manuals for DDU 7

400DX-2 - 40IN LCD 1920X1080 3000:1 VGA Dvi

Brand: Samsung Pages: 28

400DX-2 - 40IN LCD 1920X1080 3000:1 VGA Dvi

Brand: Samsung Pages: 29

Odyssey S27AG550EN

Brand: Samsung Pages: 36

Odyssey Ark Series

Brand: Samsung Pages: 42

Brand: Samsung Pages: 36

Odyssey S49CG954SU

Brand: Samsung Pages: 24

Brand: Angel Pages: 2

Brand: Samsung Pages: 2

Brand: Eizo Pages: 2

Brand: Daewoo Pages: 10

FusionAmp OLED Display

Brand: Hypex Electronics Pages: 12

Brand: TechLine Pages: 26

Brand: NASA Marine Pages: 12

HIS-ML15-***E Series

Brand: Hope Industrial Systems Pages: 24

Brand: Hanns.G Pages: 23

Brand: Summer Pages: 4

Brand: Beurer medical Pages: 120

MOTORSAVER 455-480R

Brand: SymCom Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands