Bosch DDU 7 Manual Download Page 31 | Manualshive

Page: 31 / 156

background image

Display Unit DDU 7

Display Configuration | en

31

Bosch Motorsport

Manual

04.02.2019 | V 02 |

Configurable
LEDs

Display area

Tabs to switch
between
different items/
pages

8.2

Display element configuration

8.2.1

Numeric display element

Adding a numeric display element to display page

The ‘Large Element’ and the ‘Medium Element’ numeric display elements differ in element and
font size. The element and font size can be changed using the Numeric Wizard.

Notice!

In this view the displayed values are random values and do not show the real values of the
measurement channels.

1.

Drag a numeric display element from the Toolbox and drop it on the display page. A
message in the numeric element box shows that it is not linked to a measurement
channel.

Drag + Drop

2.

Drag a measurement channel from the Data Area and drop it on the numeric display
element.

«
...
29
30
31
32
33
...
»

Summary of Contents for DDU 7





























































































































































Reviews:

No comments

Related manuals for DDU 7

Brand: iBaby Pages: 15

Brand: M-system Pages: 8

Brand: Banner Pages: 4

YUR.VISION YV24WBH1 -

Brand: YURAKU Pages: 2

YUR.VISION YV216WB2

Brand: YURAKU Pages: 11

YUR.VISION YV19WB1 -

Brand: YURAKU Pages: 2

Brand: Samtron Pages: 115

dynamics 44 6085 S

Brand: Ofa Bamberg Pages: 18

Brand: protech Pages: 46

Brand: BenQ Pages: 44

PTE0700 V2 Series

Brand: Pakton Pages: 18

PlasmaWall XP-OPAL50 DHD

Brand: Runco Pages: 1

diamond pro 1000 TFX1105SKTKW

Brand: Mitsubishi Pages: 34

Brand: ViewSonic Pages: 65

Brand: PYLE Audio Pages: 16

Brand: Task Force Tips Pages: 20

Brand: ViewSonic Pages: 88

Brand: Valcom Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands