Bosch DDU 7 Manual Download Page 97

Page: 97 / 156

Display Unit DDU 7

Online Measurement | en

Bosch Motorsport

Manual

04.02.2019 | V 02 |

A green dot and background at the device in the project view and the DDU 7 Project Tree
indicate a successful download and system consistency.

If the system’s configuration in RaceCon has been changed, the dot and background becomes
yellow and a configuration download is necessary.

11.1.3

Configuration download

Right-click on DDU 7 in the DDU 7 Project Tree.

Select ‘Download configuration’.

The configuration download starts.

A Green dot and background indicate a successful download.

11.2

Setting up an online measurement

DDU 7 supports online measurement of sensor values and diagnostic variables.
Expand ‘Measurement Container’ and ‘Measurement Folder 1’ in the Project Tree and double-
click on ‘Sheet1’. ‘Sheet 1’ is opened in the Main Area.

From the context menu of the project, new measurement pages can be created.

Summary of Contents for DDU 7





























































































































































Search results

Summary of Contents for DDU 7

Reviews:

Related manuals for DDU 7

Brands by name

Popular brands

Bosch DDU 7, Manual

Search results

Summary of Contents for DDU 7

Reviews:

Related manuals for DDU 7

Brands by name

Popular brands