Bosch DDU 7 Manual Download Page 119

Page: 119 / 156

Display Unit DDU 7

Recording and Telemetry | en

119

Bosch Motorsport

Manual

04.02.2019 | V 02 |

Drag + drop

Click on FM 40 in Project Tree to display the Properties Menu.

Path of configuration folder of WDServer on receiver PC
(usually ...\WDServer\DCP) to store telemetry configuration file

Project key (1111 ... 9999)

Baudrate of Display (must match baudrate of FM 40)

Transmission pause
5 % recommended for improved re-syncronization

Adding channels to telemetry

Expand the list of ‘Loggers’ by clicking on ‘+’ in the DDU 7 Project Tree.

Double-click on ‘Recording’ in DDU 7 Project Tree.
The recording configuration is displayed in the Main Area.

Click ‘Edit channel(s)’.
The ‘Edit Recording Channels’ window appears.

Choose between ‘Fast/Slow block’ transmission.
See chapter ‘Adding a recording group’ for information about ‘Fast/Slow block’.

Summary of Contents for DDU 7





























































































































































Search results

Summary of Contents for DDU 7

Reviews:

Related manuals for DDU 7

Brands by name

Popular brands

Bosch DDU 7, Manual

Search results

Summary of Contents for DDU 7

Reviews:

Related manuals for DDU 7

Brands by name

Popular brands