Bosch DDU 7 Manual Download Page 12

Page: 12 / 156

en | Technical Data

Display Unit DDU 7

04.02.2019 | V 02 |

Manual

Bosch Motorsport

USB-Port unlocked (Rugged USB flash drive 2
GB Bosch File System (BFS) format included,
works with Bosch File System (BFS)
preformatted USB Flash drive only)

F 02U V01 133-02

Adapter cable to USB-Port (included in
Upgrade)

F 02U V01 343-01

Adapter for wiring harness (included in
Upgrade)

F 02U 002 996-01

Software Upgrade 2

CCP-Master (ASAP2 file from ECU
manufacturer required)

F 02U V01 134-01

Connectors and Wires

Motorsport connector
AS

2-14-35PN at DDU7

37 pins

Mating connector
AS 6-14-35SN

F 02U 000 453-01

Communication

CAN interfaces

Ethernet 100BaseT

Laptrigger input

RS232

Telemetry, GPS

Configuration via RaceCon

Over Ethernet or MSA-Box II

Installation Notes

The required software (.pst file) for this device is available in the download area of our
homepage www.bosch-motorsport.com.

Summary of Contents for DDU 7





























































































































































Search results

Summary of Contents for DDU 7

Reviews:

Related manuals for DDU 7

Brands by name

Popular brands

Bosch DDU 7, Manual

Search results

Summary of Contents for DDU 7

Reviews:

Related manuals for DDU 7

Brands by name

Popular brands