Billion BIPAC-645 User Manual Download Page 71

Page: 71 / 82

enter remote network IP address (Unspecified): 192.168.167.0

enter remote network IP netmask (Unspecified): 255.255.255.0

Router>

Example 3 – Internet Access through EWAN port:

Router> add profile wilson

The system is currently in Advanced Mode, press Ctrl-E to switch to

Express Mode.

Add new connection profile “wilson” ...

enter interface type (ISDN, ISDN/EWAN): ewan

enter access type: 1> internet access only

2> remote office dial in/out (1): 1

enter encapsulation type (Ethernet, Ethernet/PPPoE):

Profile wilson is configured successfully. Configuring Network

Protocol over wilson ..

enable IP routing (Yes, yes/no):

obtain IP addresses automatically (Yes, Yes/No):

enter host name [system name] (Local Router):

clear profile statistics [Profile Name]

The statistics fields in the specified static profile are reset to initial values when the

Profile Name

parameter is provided in command line. If no

Profile Name

is specified, all profile statistics are cleared.

connect profile <Profile Name>

For switched profiles, this command activates the profile as if a trigger occurred. This command has no
effect on leased line profiles.

delete profile <Profile Name>

The specified profile is removed from the system.

disable profile <Profile Name>

The administrative state of the specified profile is set to “disabled”. A profile cannot be used unless it is
enabled.

disconnect profile < Profile Name>

For active switched profiles, this command terminates the connection as if an idle timeout occurred. This
command has no effect on leased line profiles.

enable profile <Profile Name>

The state of the specified profile is set to “enabled”. Only enabled profiles are available for use. A
profile’s state is set by default to

enabled

when it is created.

Summary of Contents for BIPAC-645



















































































Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands

Billion BIPAC-645, User Manual

Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands