Billion BIPAC-645 User Manual Download

Page: 16 / 82

Profile Name:

the name that you will use to identify this Internet access profile.

EWAN IP Address:

the IP address of your EWAN.

EWAN IP Netmask:

the IP Netmask of your EWAN.

ISP Gateway IP Address:

the IP Address of your ISP Gateway

Primary DNS IP Address:

the IP Address of your Primary DNS.

Secondary DNS IP Address:

the IP Address of your Secondary DNS

Step 4:

If you choose

via DHCP

for the selection of

Obtain IP Address Automatically.

The following

screen will be displayed. Enter the following information and then Click

Apply.

Profile Name:

the name that you will use to identify this Internet access profile.

(Optional) Host Name (System Name):

the Host Name provided by your system.

Step 5

: If you choose

via PPP over Ethernet

for the selection of

Obtain IP Address Automatically.

The

following screen will be displayed. Enter the following information and then Click

Apply and Test.

Summary of Contents for BIPAC-645



















































































Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands

Billion BIPAC-645, User Manual

Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands