Billion BIPAC-645 User Manual Download Page 65

Page: 65 / 82

is directly attached to the router (i.e., the destination is on the same LAN the router is connected to), or
the destination is reachable through an unnumbered serial interface.

The meanings of the flags are:

Host

S Static

Route

G Gateway
C Cloned

Entry

Example:

Router> show ip routing table

Destination Netmask

Gateway

Hop

IfName

Flags

-------------------------------------------------------------------

40.0.0.0

lan

192.168.168.0

255.255.255.0

lan

10.0.0.1

20.0.0.1

20.0.0.2

ppp2

110.0.0.0

255.0.0.0

40.0.0.5 5

lan

120.0.0.0

255.0.0.0

40.0.0.5 1

lan

show ip statistics

Description:

This csommand displays IP routing related statistics.

Example:

Router> show ip statistics

Received

Transmitted

-----------------------------------------------------------------

Packets

received

17418

Datagrams

generated

Locally

123

Packets

Forwarded

15768

Datagrams Delivered to Upper Layer

3241

Raw

Packets

Sent

1650

Redirects

Sent:

Packet drops:

Header

Errors

Unknown

Protocols

Not

Forwardable:

DONT-FRAGMENT

Bit

ON:

No Buffers:

No Route:

fragmentation:

Total

Fragments

Datagrams

Reassembled

Datagrams

Fragmented

for

Output

Summary of Contents for BIPAC-645



















































































Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands

Billion BIPAC-645, User Manual

Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands