Billion BIPAC-645 User Manual Download

Page: 68 / 82

Router> show port

Port Name : isdn

Port Type :

ISDN

Admin Status: Enabled

Op State:

Down

Directory#1: 5551111

Directory#2:

5552222

Sub-addr Req:

Switch Type: Europe (ETSI)

Advice of Charge

Unit price:

Unspecified Currency:

Unspecified

Port Name : ewan

Port Type :

EWAN

Admin State : Enabled

Data Link Type:

Ethernet

show port <port name>

Description:

This command displays the configuration of a WAN interface port.

Example 1:

Router> show port isdn

Port Name : isdn

Port Type :

ISDN

Admin Status: Enabled

Op State:

Down

Directory#1: 5551111

Directory#2:

5552222

Sub-addr Req:

Switch Type: Europe (ETSI)

Advice of Charge

Unit price:

Unspecified Currency:

Unspecified

Router>

Example 2:

Router> show port ewan

Port Name: ewan

Port Type:

EWAN

Admin State: Enabled

Data Link Type:Ethernet

Speed:

10 Mb

MAC Address:

90-00-12-34-56-79

Profile type: EWAN

Admin. State: Enabled

Encapsulation: Ethernet MAC

Address:

90-00-12-34-56-79

Oper. State: Down

Max Receive Unit:

1500

System Name:Local Router

show port statistics <port name>

Example 1:

Router> show port statistics isdn

Received:

Transmitted:

----------------------------------------------------------------

D-Channel

Total

Octets:

230

347

Total

Packets:

Summary of Contents for BIPAC-645



















































































Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands

Billion BIPAC-645, User Manual

Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands