Billion BIPAC-645 User Manual Download

Page: 70 / 82

Existing profiles are edited also using the “add profile” command. In this case, the defaults shown are the
existing configured values.

This router only support one profile over EWAN interface. When an ewan profile is configured, the

following new added profile(s) will select ISDN automatically. User can modify the ewan profile by using
“add profile” command or “delete profile”, then “add profile” again.

⊕

add profile <Profile Name>

Example 1 – Set up an Internet Access Profile over ISDN

Router> add profile daniel

The system is currently in Advanced Mode, press Ctrl-E to switch to

Express Mode.

Add new connection profile “daniel” ...

Interface type: ISDN

enter access type: 1> internet access only

2> remote office dial in/out (1): 1

enter remote directory number (Unspecified): 5553333

enter ISP account name (Unspecified): user-name

enter ISP account password (Unspecified): ****

enable compression (No, yes/no):

Profile daniel is configured successfully. Configuring Network

Protocol over daniel ...

enable IP routing (Yes, yes/no):

Set this profile as IP default route (Yes, yes/no):

Router>

Example 2 – Set up a Remote Office Profile over ISDN

Router> add profile julia

The system is currently in Advanced Mode, press Ctrl-E to switch to

Express Mode.

Add new connection profile “julia” ...

Interface type: ISDN

enter access type: 1> internet access only

2> remote office dial in/out (1): 2

enter action mode (Dial only, dial only/answer only/both): d

enter remote directory number (Unspecified): 5556666

enter my account name (Unspecified): user1

enter my account password (Unspecified): ****

enable compression (No, yes/no):

Profile julia is configured successfully. Configuring Network

Protocol over julia ...

enable IP routing (Yes, yes/no):

Set this profile as IP default route (No, yes/no):

Assume one ewan profile is already configured.

Summary of Contents for BIPAC-645



















































































Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands

Billion BIPAC-645, User Manual

Search results

Summary of Contents for BIPAC-645

Reviews:

Related manuals for BIPAC-645

Brands by name

Popular brands