BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 87

Page: 87 / 183

Maintenance

BETTCHER

Industries, Inc.

Manual No. 102481
April 17, 2015

Maintenance
Whizard Quantum

Air Operating Instructions and Parts List

5-41

Assembly of Whizard Quantum

TRIMVAC

Handpiece

(Continued)

Step 7: Install Blade (Continued):

Whizard

Quantum

TRIMVAC

18:

•

Carefully insert the blade.

•

Loosen the left cover retaining screw so the housing will close.

NOTE:

Be certain that the blade is free to move in the housing. If the blade does not move freely, it

may cause the trimmer to overheat.

•

Adjust the housing for proper running clearance.

•

When the housing is properly adjusted there will
be a slight “left to right” movement, plus a light
“up and down” movement.

•

If the blade does not move “left to right” and “up
and down”, pry the housing open slightly.

•

Retighten the cover retaining screws.

NOTE:

Recommended torque of 30-40 lb-in (3.4-4.5 N-m)

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands