BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 28

Page: 28 / 183

BETTCHER

Industries, Inc.

Instructions for Operation

4-4

Instructions for Operation
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

Step 1:

Grease Cup and Ring

•

Pick up the Whizard

Trimmer.

•

Pick up the grease cup and ring. Apply a
small amount of Whizard

Special Grease

to the frame o-rings.

•

With a twisting motion, install the grease
ring onto the frame over the o-rings.

Be careful not to
squeeze the o-rings
out of their grooves, or
they could be trapped
and damaged.

•

Rotate the grease cup to the desired position.

Step 2:

Spacer Ring

•

Select the spacer ring or optional thumb
support.

•

If the spacer ring is used

, Slide the spacer ring

onto the frame, small end first.

Grease Cup

Grease Ring

Frame O-Rings (2)

Frame

Spacer Ring

Frame

Small End

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands