BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 95

Page: 95 / 183

Maintenance

BETTCHER

Industries, Inc.

Manual No. 102481
April 17, 2015

Maintenance
Whizard Quantum

Air Operating Instructions and Parts List

5-49

Inspection and Maintenance of Power Unit

Inspection and maintenance should be performed after every 80 hours of use.

Handle

•

Clean the handle with warm soapy water and a soft brush. Remove any build up from the
grooves. Rinse the handle and dry thoroughly.

•

Inspect the handle for the following and replace if damage is detected.

•

Inspect the handle grip for tears, cuts, or wear.

•

Inspect the handle grooves for nicks or wear.

•

Inspect the handle I.D. for dents.

Grip

Groove (2)

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands