manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual, Page: 45 / 183

Share
Download
BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 45

 Instructions for Operation 

 

 BETTCHER 

  Industries, Inc.

 

Manual No. 102481 
April 17, 2015 

 Instructions for Operation  
Whizard Quantum

®

 Air Operating Instructions and Parts List 

4-21

 

Blade Changing 

(Continued) 

 

•

 

Loosen the left cover retaining screw to allow the housing to close. 

•

 

Tighten the right cover retaining screw. 

•

 

With left cover retaining screw ½ turn loose, adjust housing for proper fit. 

•

 

Gently pry the housing open until the blade rotates freely and has enough clearance to 
allow the blade to move forward and backward in the housing.  Only a slight amount of 
movement is necessary.  

•

 

Tighten the cover retaining screws to the recommended torque. 

 

NOTE:  

Recommended torque of 30-40 lb-in (3.4-4.5 N-m). 

IMPORTANT:  

Be sure that the blade is free to move in the housing.  If the blade does 

not move freely, it may cause the trimmer to overheat. 

 

 

 

 

Housing Slot

Screwdriver

Pivot Support
Point

Left Cover
Retainging Screw

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Reviews:

No comments