BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 58

Page: 58 / 183

BETTCHER

Industries, Inc.

Maintenance

5-12

Maintenance
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Inspection and Maintenance of Handpiece

(Continued)

Drive Adapter Assembly

•

Inspect the drive adapter assembly for the following. Replace the drive adapter assembly
if damaged.

•

Inspect the square end of the driver for rounded corners.

•

Inspect the retaining ring for damage.

•

If retaining ring has moved out of the groove or is missing, replace drive adapter
assembly.

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands