BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 26

Page: 26 / 183

BETTCHER

Industries, Inc.

Instructions for Operation

4-2

Instructions for Operation
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Optional Thumb Support

Your Bettcher Quantum

Air Trimmer has been supplied with a spacer ring and an

optional thumb support. If using the optional thumb support, the operator’s thumb should
be fully supported and rest comfortably in the support. The thumb support has been
optimized to fit most hands comfortably.

NOTE

If the operator normally wears a glove, this process

should be done with the glove(s) used in normal operation.

We do not recommend the use of Nitrile gloves in direct

contact with the Whizard Quantum

Air handles because

the gloves may become slippery.

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands