BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 39

Page: 39 / 183

Instructions for Operation

BETTCHER

Industries, Inc.

Manual No. 102481
April 17, 2015

Instructions for Operation
Whizard Quantum

Air Operating Instructions and Parts List

4-15

Depth Gauge Adjustment

(Continued)

Optional Adjustable Fat (F) and Skinner (S) Disc Gauges for the Whizard
Quantum

Air Models 850, 1850, 1000 and 1300

•

Hold the handpiece with the blade facing
downward.

•

Adjustments – Turn the adjustment knob

clockwise

for a thicker cut, or

counterclockwise

for a thinner cut.

Important:

Take care not to turn the

adjustment knob too far as the disc may
disengage from the shaft.

Sharp blades may cause cut injury!
For proper protection of hands, a protective glove
should be used when operating this equipment and
during the handling of blades.

Always disconnect the tool from the air supply prior
to servicing.

WARNING

Adjustment
Knob

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands