BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 92

Page: 92 / 183

BETTCHER

Industries, Inc.

Maintenance

5-46

Maintenance
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Power Unit Maintenance

Required Tools for Power Unit Maintenance

1 – Spanner Wrench (Supplied with your Whizard Quantum

Air Trimmer)

Disassembly of Power Unit

Step 1: Remove Cap

•

Remove the cap.

NOTE:

Do not discard the cap.

Step 2: Unscrew Retainer

•

Unscrew the retainer using the supplied spanner wrench. The retainer is a left-handed
thread and must be turned to the right (clockwise) to unscrew.

Power Unit

Cap

Power Unit

Spanner Wrench

Retainer

Spanner Wrench

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual, Page: 92 / 183

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews: