manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual, Page: 82 / 183

Share
Download
BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 82

  BETTCHER 

  Industries, Inc.

 

 Maintenance

 

 

5-36 

Maintenance 
Whizard Quantum

®

 Air Operating Instructions and Parts 

List 

Manual No. 102481  
April 17, 2015 

 

Assembly of Whizard Quantum

®

 TRIMVAC

®

 Handpiece

 (Continued) 

 

Step 3:  Install Bearing: 

 

•

 

Push the handpiece bearing into the frame 
bore and align the bearing flat with the 
frame flat. 

•

 

The bearing should go in with minimal 
effort and not require pressing. 

•

 

Do not force the bearing in.  If the bearing 
does not go in easily, check frame and 
bearing for damage or build-up. 

 
 
 

 
 

 
 

Step 4:  Install Pinion: 
 

•

 

Insert the pinion into the bearing bore. 

•

 

The pinion should go in with minimal effort and 
not require pressing. 

•

 

Do not force the pinion into the bearing.  If the 
pinion does not go in easily, check the bearing 
and pinion for damage or build-up. 

•

 

The pinion should sit flush against the bearing.  
If it does not, rotate the pinion to seat it flush 
with the bearing. 

 

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Reviews:

No comments