BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 52

Page: 52 / 183

BETTCHER

Industries, Inc.

Maintenance

5-6

Maintenance
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Disassembly of Handpiece

(Continued)

Step 3: Remove Blade:

•

Hold the tool with
the blade side up.

•

Loosen only the left
cover retaining screw.

NOTE

A slight tension on the left

cover screw will allow the blade
housing to stay open on its own.

•

Insert a screwdriver into the housing
slot.

•

Using the frame as the support point,
spread
open the housing, just far enough to
remove the blade.

•

Carefully remove the blade.

Housing Slot

Screwdriver

Pivot Support
Point

Left Cover
Retainging Screw

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands