BETTCHER INDUSTRIES Whizard Quantum Air 1000 Operating Instructions & Parts List Manual Download Page 79

Page: 79 / 183

Maintenance

BETTCHER

Industries, Inc.

Manual No. 102481
April 17, 2015

Maintenance
Whizard Quantum

Air Operating Instructions and Parts List

5-33

Blade Sharpening of Whizard Quantum

TRIMVAC

Handpiece

(Continued)

Whizard Quantum

TRIMVAC

18 Sharpening

•

With the trimmer running, insert the blade into the TRIMVAC

Sharpener. The plastic

cap on the top of the sharpener will guide the handpiece into the sharpener.

•

Press the blade lightly onto the sharpening and steeling rods for a few seconds.

Summary of Contents for Whizard Quantum Air 1000
























































































































































































Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Air 1000

Reviews:

Related manuals for Whizard Quantum Air 1000

Brands by name

Popular brands