manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 85

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 79 

9.4.21 

Removing Tubing from Barbed Fittings 

 

Disconnect the air line. 

 

 

 

 

 

FIGURE #71 

 

 

 

FIGURE #72 

 

 
Pull back the locking collar if present. 
 
Use a small screwdriver to pry the tube end over the barb of the fitting.  Insert the screwdriver 
under the tubing and push it up to the barb.  Pry the tubing over the barb while pulling on the 
tubing with your other hand, as shown.  

Take Care Not To Damage The Barb

. 

 
 

SECTION 10.0  CLEANING 

 

The AirShirz

®

 is constructed of corrosion resistant, easily cleanable materials.  The metallic parts 

are either stainless steel or aluminum with an anodize coating.  The plastic parts are acetyl, nylon, 
polypropylene, nitrile, or polysulfone.  The tubing is polyurethane. 
 
Mild detergents may be used but alkaline solutions should be avoided. 

Locking Collar 

Tubing 

Fitting 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands