manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 59

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 53 

9.4.4 

Blade Latch Installation 

 
Disconnect the air line. 

 
Clean area around post and re-install latch ring with the projections at the top edge as shown in 
Figure #43.  Rotate latch ring between the unlocked and locked positions.  The tang

s

 of the latch 

ring should engage the flats on the post to produce a "detent" action in both positions.  If this 
detent action does not hold the latch ring in the unlocked position, replace the latch ring.   
 
Re-install the cover (refer to Section 9.4.2). 
 

9.4.5 

Disconnecting Master Link 

 
Disconnect the air line. 

 
Remove blade set and cover (refer to Section 9.4.1) 
 
Push the rod fully into the power cylinder. 
 
Remove the screw holding the halves of the master link together. 
 
Lift the top plate of the master link off the pivot pins and set aside.  Push the end of the master link 
attached to the control valve off the rod pin and rotate it forward. 
 

 

 

 

 

FIGURE #44 

 

 

 

FIGURE #45 

TOP PLATE 

MASTER LINK SCREW 

ROD FULLY IN 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands