manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 33

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 27 

 

8.2.3 

MicroBreak Strap Installation 

 

•

 

Put the top end of the strap, (end without the buckle), through the thumb hole, from the 
hand side of the power unit, such that the snaps are facing up. 

 

•

 

Wrap this end around and over the valve block of the power unit.  Then slip the strap into 
the clip on top of the valve block. 

 

 

FIGURE #22 

 

•

 

Pull the end until the snap is aligned with the mating button near the middle of the strap.  
Snap these together.

 

 

•

 

Route the buckle end around the power cylinder and snap it to the frame.

 

 

•

 

If the adjustment was changed, it will need to be redone (see Section 8.2.1). 

 

 

Clip 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands