manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 23

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 17 

SECTION 7.0 

INSTALLATION 

 
The AirShirz

®

 requires a supply of clean air in the range of 80 to 120 PSI (5.5 - 8.3 Bars).  

The location of the connection to this air supply should be carefully planned to provide a 
comfortable routing of the coiled tubing away from the work activities.  The connection 
should be close enough to allow the operator full freedom of motion within the work space, 
yet not so close as to cause the coiled tubing to bunch and tangle.  Note that the spent air is 
exhausted at the connector-end of the coiled tubing.  This discharged air should be directed 
away from the operator and away from the product. 
 
If the air supply does not already have a filter and pressure regulator, these items will need 
to be installed.  If you purchased these items from Bettcher Industries, they will  fit onto 
size 1/4 NPT pipe threads.  The order of installation is very important.  The air filter is 
installed 

upstream

 from the regulator and air gage as shown in the following illustrations. 

 

 

NOTE

: 

USE A THREAD SEALING COMPOUND WHEN 

 

MAKING PIPE CONNECTIONS

. 

 

 
The AirShirz

®

 filter/coupler attaches to the outlet end of the air supply line and can be 

installed in either of two configurations: 
 
 
 
 
 
 
 
 
 
 
 
 
 

7.1  

Configuration #1 - Permanent Mount To End of Air Supply Pipe 

 
Use a 3/4 inch open end wrench to hold the filter body while using a 9/16 inch wrench to 
unscrew the standard male quick connector. 

 

EXHAUST 

AIRSHIRZ® 

FILTER/COUPLER 

1/4 NPT PIPE 
THREADS 

4” 

PRESSURE 

REGULATOR 

AIR 

FILTER 

REPLACEMENT 

ELEMENT 

AIR 

SUPPLY 

CONFIGURATION #1 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands