manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 40

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 34 

SECTION 9.0 

MAINTENANCE 

 

9.1  

Daily/Periodic Checks 

 

9.1.1 

Blade Sharpness 

 

If blades fold over instead of cutting through the product, then they need to be sharpened.  Also see 
Section 9.3.3 Checking Blade Sharpness.  Disconnect the air supply and remove the blade set 
(reference Section 8.1.2). 

 

 

 

WARNING

 

 

 

THE BLADES ARE VERY SHARP

.

  WEAR CUT RESISTANT

 

GLOVES WHILE OPERATING THE AIRSHIRZ

®

 

 

 

 

WARNING 

 

 

AIRSHIRZ

®

 MAGNUM

 

AMPUTATION IS POSSIBLE

.

  

THE BLADES ARE VERY SHARP

.

  WEAR METAL 

MESH CUT RESISTANT GLOVES WHILE OPERATING THE 

AIRSHIRZ

®

 

M

AGNUM

.

 

 
 

Open the blades fully.  Look along the cutting edges.  If the edges are not nicked or overly 
rounded, the sharpness may be restored by "steeling".  For optimum sharpness, use the Bettcher 
Industries Model 212 EdgeKing Scissor Sharpener System. 

 

9.1.2 

Leak Tests 

 

A small amount of air leakage will not significantly affect the operation of the AirShirz

®

.  

However, large leaks will cause the AirShirz

®

 to operate at reduced power and speed.  There are 

two simple tests that may be done. 

 

 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands