BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 19

Page: 19 / 110

OPERATING

BETTCHER

AIRSHIRZ

INSTRUCTIONS

INDUSTRIES, INC. Rev. September 24, 2016

Page 13

3.2

Safety Recommendations and Warnings (Continued)

WARNING

SHARP BLADES MAY CAUSE CUT INJURY

ALWAYS DISCONNECT POWER

AND REMOVE THE BLADE SET PRIOR TO SERVICING

WARNING

THE BLADES ARE VERY SHARP

WEAR CUT RESISTANT

GLOVES WHILE OPERATING THE AIRSHIRZ

WARNING

AIRSHIRZ

MAGNUM

AMPUTATION IS POSSIBLE

THE BLADES ARE VERY SHARP

WEAR METAL

MESH CUT RESISTANT GLOVES WHILE OPERATING THE

AIRSHIRZ

AGNUM

WARNING

ALWAYS CLOSE THE BLADES AND LOCK

THE BLADE LATCH WHEN NOT IN USE

SECTION 4.0

SAFETY FEATURES

The AirShirz

is designed to be safe and easy to use. The functions of these features should be

clearly understood before operating this tool.

Summary of Contents for AirShirz















































































































Search results

Summary of Contents for AirShirz

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Search results

Summary of Contents for AirShirz

Reviews:

Brands by name

Popular brands