manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 25

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 19 

SECTION 8.0 

INSTRUCTIONS FOR OPERATION 

 

8.1  

The Blade Set  

 

 

 

CAUTION 

 

 

THE BLADES ARE VERY SHARP

. 

ALWAYS WEAR CUT RESISTANT GLOVES WHILE HANDLING THE BLADES

. 

KEEP THE BLADES IN THE CLOSED POSITION WHILE HANDLING

. 

 

The blades are supplied as a precision matched set, pre-adjusted at the factory for optimum 
performance.  

Do not dismantle or change the adjustment on new blade sets

.  The mounting 

screw is designed to float within the assembly and will not fall out.  It should not be removed. 
 
The blade set is shipped in the normal 

"blades closed"

 position.  This protects both the operator 

and the cutting edges. 
 
The blade set consists of two blades - a fixed blade and a movable blade.  The fixed blade has two 
holes which slide onto the two pins in the power unit.  The movable blade has a slot which fits 
over a roller on the internal driving linkage of the power unit.  This roller is visible at the top of the 
pocket in the power unit as shown. 

 
 
 
 
 
 
 

 
 
 
 

 
 

 

 

 

 

 

WARNING 

 

 

NEVER LEAVE THE AIRSHIRZ

®

 

WITH THE BLADES IN THE OPEN POSITION

. 

 

 

ROLLER 

FIGURE #6 

 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands