manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 28

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 22 

 

8.1.1 

Blade Installation Sequence   (Continued) 

 

•

 

Start the blade set over the pins and wiggle the blades slightly while pushing them into the 
power unit.

 

 

 

 

FIGURE #12 

 

•

 

If the blade set does not drop fully into the pocket, it is because the slot in the movable 
blade is not exactly aligned with the roller.  To align the slot, press down at the corner of 
the fixed blade with your thumb while spreading the blades slightly with your gloved hand.  
When the slot and the roller become aligned, the blade set will drop into place. 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

FIGURE #13 

 

•

 

Use a 1/2 inch wrench to tighten the blade set mounting screw. 

 

Spread the Blades 

Open Slightly 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands