manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 2

OPERATING  

BETTCHER  

          AIRSHIRZ

®

 

 INSTRUCTIONS 

              INDUSTRIES, INC.                                         Rev.  September 24, 2016

 

 

Page i 

Information in this document is subject to change without notice. 
 
No part of this document may be reproduced or transmitted in any form or any means, electronic 
or mechanical, for any purpose, without the express written permission of Bettcher Industries, Inc. 
 
Written permission to reproduce in whole or part is herewith granted to the legal owners of the 
AirShirz

®

 with which these Operating Instructions have been supplied. 

 
Operating Instructions in other languages are available on request.  Additional copies of Operating 
Instructions are available by calling or writing your Regional Manager, or by contacting: 
 

BETTCHER INDUSTRIES, INC. 

P.O. Box 336 

Vermilion, Ohio  44089-336 

U.S.A. 

 

 

Telephone:  440/965-4422 

 

(In the U.S.A.):  800/321-8763 

 

Fax:  440/328-4535 

 

www.bettcher.com

 

 
 
 

 

The Information Provided in these Operating Instructions is 

Important to your Health, Comfort and Safety. 

For Safe and Proper Operation, Read this Entire Manual 

Before Using this Equipment.

 

 
 
 
 
 

 

 
 

Copyright 

 2016 by Bettcher Industries, Inc. 

All Rights Reserved. 

Original Instructions 

 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands