manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 57

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 51 

9.3.5 

Replacing Blade Pivot Bushings   (Continued) 

 

 

 

WARNING 

 

 

WEAR CUT RESISTANT GLOVES ON BOTH HANDS

.

 

 
Apply a light coating of Bettcher

®

 Max-Z-Lube to the mating surfaces of the blades near the pivot 

as shown in Figure #40.  Pick up the fixed blade and align the flat on the pivot nut with "D" shaped 
hole on the blade.  Push the pivot nut into the hole and hold it in place with your finger.  Place the 
movable blade over the pivot nut, and against the fixed blade.  Place the locknut, with the plastic 
washer, onto the blade and screw it into the threads of the pivot bushing (clockwise). 
 
The lock nut should produce some resistance to turning.  Use a 5/8 inch wrench to screw the 
locknut in until it just contacts the blade.  Install the blade screw, then perform the blade nut 
adjustment (see Section 9.3.4). 
 

9.4  

Assembly/Disassembly Procedures 

 

 

 

WARNING 

 

 

CLOSE THE BLADES

,

 ENGAGE THE BLADE LATCH

, 

THEN DISCONNECT THE AIR LINE AND REMOVE THE BLADE SET

 

BEFORE PERFORMING ANY OF THE FOLLOWING PROCEDURES

! 

 

NOTE: 

Place the Power Unit on a Clean, Well-Lit Table with 

Enough Space to Set Aside Removed Parts. 

 

9.4.1 

Cover Removal 

 
Disconnect the air line. 

 
Remove the cover pivot screw.  Clean any debris from the cover and linkage.  Inspect the cover for 
cracks. 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands