manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 37

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 31 

 

8.4  

Fault Detection & Correction   (Continued) 

 

YES

SMOOTHNESS ADJUSTMENT 

MAY BE TOO FAR 

CLOCKWISE.  READJUST 

SMOOTHNESS CONTROL 

(9.2.2)

IS FINGER LOOP OPENING 

FULLY?

BLADES NOT OPENING 

FULLY TO 45 DEGREE 

ANGLE

REPLACE CONTROL VALVE

(9.4.15)

IS THE BLADE DRIVE 

ROLLER ON MAIL LINK IN 

GOOD CONDITION WITH 

LITTLE OR NO SIDE PLAY?

IS CYLINDER ROD AT FULL 

STROKE INWARD WHEN 

FINGER LOOP IS OPEN 

FULLY?

ADJUST 

SMOOTHNESS 

CONTROL (9.2.2)

READJUST 

STROKE  (9.2.3)

RECHECK 

SMOOTHNESS

CHECK THAT BLADE 

LATCH IS OPEN FULLY 

AND IN THE CORRECT 

DETENT POSITION 

(9.4.3)

REPLACE DRIVE 

LINK ASSEMBLY 

(9.4.11)

IF NOT OK

YES

NO

NO

NO

IF FINGER LOOP STILL 

NOT OPENING FULLY, 

SEE SECTION ON 

FINGER LOOP

(9.4.9 & 9.4.10)

IF OK NOW, RETURN TO SERVICE

ADJUST 

SMOOTHNESS 

CONTROL (9.2.2)

ADJUST STROKE 

CONTROL (9.2.3)

RECHECK 

SMOOTHNESS

YES

 
 

 

 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands