manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 27

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 21 

 

8.1.1 

Blade Installation Sequence   (Continued) 

 

•

 

Confirm that the roller is at the top of the pocket.  If not, it can be moved by pushing 
forward on the linkage at the power cylinder rod.  (See Figure #10). 

 

 

 

FIGURE #10 

 

•

 

Check that the blade set mechanism and mounting area are clean. 

 

•

 

Hold the blade set by the closed blades with a gloved hand.  The fixed blade should be 
facing you and the movable blade will be behind it. 

 

•

 

Hold the power unit in your other hand so the blade pocket is facing you. 

 

•

 

Align the holes in the fixed blade with the pins on the power unit, as shown. 

 
 

 
 
 
 
 
 
 
 
 
 

 

FIGURE #11 

 

PUSH LINK 

Roller 

CLEAN 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands