manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 84

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 78 

9.4.20.2  Filter Element Replacement 

 

 

 

 
Disconnect the air line. 

 

 

 
 

FIGURE #70B 

 

The in-line filter is located ahead of the quick connect coupling to the AirShirz

®

  coiled  air  line.  

Remove this section from the air line if it is on a quick connector, otherwise, 

SHUT OFF THE 

AIR TO THIS LINE AND BLEED OFF ALL PRESSURE BEFORE PROCEEDING

. 

 

 

 

WARNING 

 

 

BE SURE ALL AIR PRESSURE IS REMOVED FROM THE SUPPLY LINE

 

WHERE THE FILTER IS MOUNTED BEFORE PROCEEDING

. 

 
Using two adjustable wrenches, or 3/4 inch open-end wrenches, unscrew the filter end cap from 
the filter body. 
 
Carefully remove the filter element.  Watch for the rubber washer and rear spring. 
 
Clean out inside of valve body and install a new element so the small, closed-end fits into the small 
side of the spring in the valve body, as shown. 
 
Be sure the rubber washer is in the recess of the end cap.  Then install the end cap back onto the 
filter body and tighten. 

Filter End Cap 

Rubber Washer 

Filter Element 

Spring 

Filter Body 

Filter Element 

and Washer Kit 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands