manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 61

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 55 

9.4.7 

Servo Linkage Removal   (Continued) 

 
Remove the master link from the underside of the middle pin if it has not fallen off on its own. 
 

 

 

CAUTION 

 

 

IF IT IS NOT INTENDED THAT THE FINGER LOOP BE REMOVED AT THIS TIME

, 

BE SURE IT IS SEATED FULLY ONTO THE POST AND DO NOT DISTURB IT

. 

 

9.4.8 

Servo Linkage Installation 

 
Disconnect the air line. 

 
Wipe clean all links, screw, small washer, and the finger loop post.  Inspect all holes and slots for 
signs of wear.  All pivoting and sliding parts should fit together with little or no side play. 
 
Install one end of the master link to the underside of the middle pin.  Install the top plate onto the 
top side of the middle pin and loosely install the small screw to hold the master link and top plate 
together as shown below. 
 

 

 

 

 

 

 

FIGURE #48   

 

 

 

FIGURE #49 

 
Apply Bettcher

®

 Max-Z-Lube to the finger loop post. 

LARGE SIDE OF HOLE FACES SCREW 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands