manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Operating Instructions And Spare Parts List

Share
Download
BETTCHER INDUSTRIES AirShirz Operating Instructions And Spare Parts List Download Page 31

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 25 

 
8.1.2 

Blade Removal Sequence  (Continued)

 

 

•

 

Use a gloved hand to grab the blade set by the closed blades.  Lift the blade set off the 
guide pins. 

 
 
 
 
 

 

 
 
 
 

FIGURE #19 

8.2  

Microbreak Strap 

 

A MicroBreak Strap has been provided on the AirShirz

®

  power unit which allows the hand 

additional comfort.  This strap is adjustable to the operator's hand.  It is easily disengaged or 
removed at the snap buttons.  

The Top Snap Is Only Removed For Cleaning Or Replacement

.  

The  AirShirz

® 

is shipped with the MicroBreak Strap mounted properly.  Before detaching the 

strap, the routing should be examined and compared to Figure #21 below. 

 

 

 

 

FIGURE #20 

 

 

 

 

FIGURE #21 

 

 

 

 

Bottom Snap 

Strap Length 

Adjustment 

Top Snap 

Summary of Contents for AirShirz















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands