manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

     

Omnisense 7000S/8000S     

4-17

Cable Connections

•

Insert the keyboard/mouse connector into the 
keyboard socket ("7 Keyboard/Mouse socket" 
in the figure). 

•

If you are installing a printer to be used with 
Omnisense, insert the printer connector into the 
printer socket ("8 Printer output" in the figure). 

•

Connect the foot pedal to the main unit by 
inserting its connector into the foot pedal 
socket ("9 Foot-pedal socket (COM1)"9 in the 
figure).

Important safeguards/notices for printer or other 
peripheral equipment installation:

1.

All the equipment connected to Sunlight Omnisense

®

 shall 

be certified according to standard IEC 60601-1, UL2601, 
IEC950 or other IEC/ISO standards, or equivalent, applica-
ble to the equipment.

2.

When Sunlight Omnisense

®

 is used together with other 

equipment in the patient area, the equipment shall be either 
powered by an isolation transformer unless it is certified 
according to standard IEC 60601-1or UL2601, or equivalent 
safety standard.

3.

The leakage current could increase when connected to other 
equipment.

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

ACS 3200 Series Operation And Instruction Manual preview
3200 Series
Brand: ACS Pages: 56
GBC AIO Quick Start Manual preview
AIO
Brand: GBC Pages: 8
KAPSCH T600 Operator And Maintenance Manual preview
T600
Brand: KAPSCH Pages: 57
Taber 1700 Operating Instructions Manual preview
1700
Brand: Taber Pages: 27
Ecco 3800 Series Assembly, Installation And Operation Instructions preview
3800 Series
Brand: Ecco Pages: 9
Talet Equipment 3000 Series Parts & Operators Manual preview
3000 Series
Brand: Talet Equipment Pages: 17
Ace AFM-5 Operating Manual preview
AFM-5
Brand: Ace Pages: 17
ACE INSTRUMENTS Solid Operating Manual preview
Solid
Brand: ACE INSTRUMENTS Pages: 33
ACE INSTRUMENTS ALP-1 med Quick Start Manual preview
ALP-1 med
Brand: ACE INSTRUMENTS Pages: 2
ACE INSTRUMENTS ACE Easy Quick Start Manual preview
ACE Easy
Brand: ACE INSTRUMENTS Pages: 2
TapFlo DT Series Original Instruction preview
DT Series
Brand: TapFlo Pages: 35
DANA DT Series Assembly Instructions Manual preview
DT Series
Brand: DANA Pages: 8
2E PSE801 User Manual preview
PSE801
Brand: 2E Pages: 6
Above All MT Instruction Manual preview
MT
Brand: Above All Pages: 4
Cannon CT-2000 Manual preview
CT-2000
Brand: Cannon Pages: 40
NARGESA H3 Instruction Book preview
H3
Brand: NARGESA Pages: 34
Mackie Onyx Blackbird Owner'S Manual preview
Onyx Blackbird
Brand: Mackie Pages: 34
Mackworth SA400 Service Manual preview
SA400
Brand: Mackworth Pages: 38

Brands by name

Popular brands

Load more brands