BeamMed Sunlight Omnisense 7000S User Manual Download Page 214 | Manualshive

Page: 214 / 284

background image

12-2

User Guide

CHAPTER 12

Cleaning and Disinfecting Omnisense

2.

Use any cleaning detergent or mild soap suitable for external
cleaning of electrical equipment to clean the Omnisense
device. Follow the instructions of the detergent or soap man-
ufacturer.

P

RECAUTIONARY

N

OTES

:

•

Do not allow any cleaning liquid to get into the probe con-
nector sockets, the disk drives or the connector sockets and
openings on the rear panel.

•

Do not use cleaning agents that can damage or destroy plas-
tics, such as ammonia, acetone, hydrochloride acid (HCL),
etc.

The Ultrasonic Probe

CLEANING

The patient contact surface of the probe should be cleaned
immediately after use. For cleaning, it is not necessary to dis-
connect the probe from the Omnisense unit.

The following steps should be followed for cleaning the probe:

1.

If a probe cap was used, remove and dispose it before clean-
ing.

2.

To clean the probe of any acoustic gel or residues, use only
dry, soft tissues or towels. If required, use towels that are
pre-moistened with a mild detergent or soap

.

3.

The probe should be allowed to air dry if pre-moistened tow-
els are used for cleaning.

4.

Visually inspect the probe to ensure cleanliness.

P

RECAUTIONARY

N

OTES

:

•

Do not immerse the probe in water, liquid detergents or
soaps.

•

DO NOT USE scrubbing materials or hard brushes that
might scratch the probe head surface.

«
...
212
213
214
215
216
...
»

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

Brand: ABB Pages: 36

Brand: ABB Pages: 40

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 7

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 30

Brand: QBC Diagnostics Pages: 65

Brand: YYZ Lighting Pages: 3

Brand: Camp Safety Pages: 118

Brand: Ultrafast Systems Pages: 39

Brand: Mackworth Pages: 2

Brand: Hammer Pages: 42

Brand: HALDER Pages: 2

Brand: Hakko Electronics Pages: 16

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Labelmate Pages: 61

Brand: Labconco Pages: 62

Brand: Palmer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands