manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

     

Omnisense 7000S/8000S     

17-7

Working with User Sites

After checking that all parameters are correct, click 

OK

. The 

new site is now defined, and will appear on the Site Selection 
list. SOS measurements conducted with the new site selected 
will follow the parameters as you have entered them.

Editing a User Site

To make changes to a site you have created, select 

Edit Site

 

from the Research menu. The Site Design dialog box is dis-
played, exactly as it does for 

Copy Site

. Enter any desired 

changes and click 

OK

.

To remove a User Site, select the site and choose 

Delete Site

 

from the 

Research

 menu.

Special Options for Research

In the Research version of Omnisense, the 

Options

 item under 

the Administration menu provides an additional tab, labelled 

Advanced

. This dialog box allows you to set a number of 

parameters relating to the type of data that are saved from SOS 
measurements. Note that this data consumes hard disk space. 

Maxi-
mum tilt 
angle

If the angle at which the probe is applied to 
the site exceeds that specified here, 
Omnisense will stop recording SOS and the 

Acoustic Signal Acquisition

 indicator will regis-

ter failure to acquire. When the probe is 
returned to a correct alignment, Omnisense 
will automatically resume signal acquisition 
and the indicator will show green. The tilt 
angle is the angle between the surface of the 
probe and the surface of the bone. A 0

0

 angle 

is created when the probe is parallel to the 
bone.

Screen 

feature

Function

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

Sagola 610 Instruction Manual / Spare Parts List preview
610
Brand: Sagola Pages: 8
National Instruments 9403 Getting Started Manual preview
9403
Brand: National Instruments Pages: 16
Jasco PRO Series Setup preview
PRO Series
Brand: Jasco Pages: 11
Keithley 261 Instruction Manual preview
261
Brand: Keithley Pages: 32
jcb CT160 Operator'S Manual preview
CT160
Brand: jcb Pages: 166
Quincy lab GC Series Operating Manual preview
GC Series
Brand: Quincy lab Pages: 4
iFIT TT200 Patient User Manual preview
TT200
Brand: iFIT Pages: 11
Kärcher SC 2 Deluxe EasyFix Operating Instructions Manual preview
SC 2 Deluxe EasyFix
Brand: Kärcher Pages: 12
Kärcher KM 70/15 C Manual preview
KM 70/15 C
Brand: Kärcher Pages: 16
Sagola 4240 Instruction Manual preview
4240
Brand: Sagola Pages: 62
DAN NTP TECHNOLOGY DAD Thunder Core 256 Installation Manual preview
NTP TECHNOLOGY DAD Thunder Core 256
Brand: DAN Pages: 16
Beurer FM 150 Instructions For Use Manual preview
FM 150
Brand: Beurer Pages: 21
SCHUNK PFH 30 Assembly And Operating Manual preview
PFH 30
Brand: SCHUNK Pages: 35
xsto ZW4 D Series Operation Manual preview
ZW4 D Series
Brand: xsto Pages: 63
Woods RB750-4 Operator'S Manual preview
RB750-4
Brand: Woods Pages: 54
Walimex Pro LED Niova 150-F Pro 150W Bi Color Manual preview
LED Niova 150-F Pro 150W Bi Color
Brand: Walimex Pro Pages: 56
Sport-thieme 1698321 Information For Use preview
1698321
Brand: Sport-thieme Pages: 20
Fisher Scientific accumet BASIC AB 15 Manual preview
accumet BASIC AB 15
Brand: Fisher Scientific Pages: 56

Brands by name

Popular brands

Load more brands