manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

8-6

     User Guide     

CHAPTER 8

Patient SOS Measurement

statistically meaningful conclusions from an SOS result, 
the conditions of the measurement should be as close as 
possible to those used in building the baseline data. 
Therefore, 

the exact procedure given in this Guide must 

be followed for each site

.

Overall, the method of measurement with Omnisense is similar 
regardless of the site being measured, although there are some 
important points that vary from site to site. In this chapter the 
correct method for measuring the distal 1/3 radius is presented 
in detail. A careful reading of the two procedures which follow 
will ensure that you are familiar with the key points of correct 
measurement and will minimize inaccuracies in your results. 
When measuring at other skeletal sites, remember to check 
carefully for variations in the method. See Chapter 15, "Site 
Measurement Methodologies‚" page 15-1.

Positioning the limb and finding the site

S

TEP

 1 Position the patient and the limb

SOS measurement at the distal 1/3 radius has been 
defined by Sunlight clinical research at a precise 
point on the limb which facilitates the easiest and 
most reproducible measurement. This point is half-
way between the elbow and the end of the middle 
finger. However, to insure compatibility with the 
reference database, it is important to locate the site 
precisely.

Always measure the patient’s non-dominant side. In case 
of a disorder or impairment in the non-dominant limb, 
such as edema, a mass, undetachable ring or IV line, use 
the contra-lateral side instead.

Seat the patient in a chair, opposite the operator and 
close to a standard desk. 

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

Wavetek 452 Instruction Manual preview
452
Brand: Wavetek Pages: 74
Fairchild 670 Instruction Manual preview
670
Brand: Fairchild Pages: 16
Vahle VCL Series Translation Of The Original Operating Instructions preview
VCL Series
Brand: Vahle Pages: 96
made for movement Xplore User Manual preview
Xplore
Brand: made for movement Pages: 51
Campbell SkyVUE 8M Quick Deploy Manual preview
SkyVUE 8M
Brand: Campbell Pages: 2
SCHUNK PWG 130 Repair Instructions preview
PWG 130
Brand: SCHUNK Pages: 2
Osram ENCELIUM User Manual preview
ENCELIUM
Brand: Osram Pages: 4
ZAMST ZK-PROTECT Instructions For Use Manual preview
ZK-PROTECT
Brand: ZAMST Pages: 14
Elliott MONSTER HAWK Operation And Maintenance Instructions preview
MONSTER HAWK
Brand: Elliott Pages: 46
KUHN GF222T Operator'S Manual preview
GF222T
Brand: KUHN Pages: 44
Spear & Jackson BoilerMag XT Series Installation And Servicing Instructions preview
BoilerMag XT Series
Brand: Spear & Jackson Pages: 8
MAHA CONNECT Series Original Operating Instructions preview
CONNECT Series
Brand: MAHA Pages: 138
Godox UL150 Instruction Manual preview
UL150
Brand: Godox Pages: 8
HydroHoist HydroPort EPIC Installation Manual preview
HydroPort EPIC
Brand: HydroHoist Pages: 19
Datavideo TBC-6000 Instruction Manual preview
TBC-6000
Brand: Datavideo Pages: 4
ZOLL AutoPulse 100 User Manual preview
AutoPulse 100
Brand: ZOLL Pages: 88
Bacharach Portable Combustion Analyzer 24-9351 Operating & Maintenance Instructions preview
Portable Combustion Analyzer 24-9351
Brand: Bacharach Pages: 100
Eaton MEDC EV24 Technical Manual preview
MEDC EV24
Brand: Eaton Pages: 22

Brands by name

Popular brands

Load more brands