manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

     

Omnisense 7000S/8000S     

4-13

Cable Connections

from any source of heat or air-conditioning. Ensure 
also that there is room for patient and operator 
chairs near the unit, and that sufficient desk or table 
space is available for a patient to rest an arm com-
fortably.

S

TEP

 2 Attach Rear Panel Connector Cables

Insert each component connector securely into the 
corresponding socket and tighten the screws if 
required (refer to 4.2 on page 4-6).

•

Insert one end of the color display monitor data 
cable connector into the monitor socket on the 
rear panel of the main unit ("11 Monitor data 
socket" in Figure 4.2, "The Omnisense main 
unit — rear view‚" page 4-6) and insert the 
other end into the monitor. 

•

Insert one end of the color display monitor 
power cable connector into the monitor power 
socket on the rear panel of the main unit ("8 
Power outlet for LCD monitor" in Figure 4.2, 
"The Omnisense main unit — rear view‚" 
page 4-6) and insert the other end into the mon-
itor.The monitor receives electricity through 
the main unit, and does not need to be con-
nected separately to a source of electricity.

•

Insert the keyboard connector into the key-
board socket ("5 Keyboard socket" in the fig-
ure), and the mouse connector into the mouse 
socket ("6 Mouse socket" in the figure). In case 
a keyboard with integrated track ball is used, 
the keyboard connector is the one with two 
cables connected to it; the trackball connector 
has only one and should be connected to the 
mouse socket. Each connector/cable has the 
corresponding labeling.

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

Panasonic D-IMager EKL3104 Software User Manual preview
D-IMager EKL3104
Brand: Panasonic Pages: 13
Labokey 7200 Manual preview
7200
Brand: Labokey Pages: 5
E-Z Trail 550 Operator'S Manual / Parts Book preview
550
Brand: E-Z Trail Pages: 8
B&K 600 Operating Instructions Manual preview
600
Brand: B&K Pages: 10
AAON RQ SERIES Manual preview
RQ SERIES
Brand: AAON Pages: 36
Eaton Crouse-hinds series Technical Manual preview
Crouse-hinds series
Brand: Eaton Pages: 32
G-Lab DR-2 User Manual preview
DR-2
Brand: G-Lab Pages: 16
G&G T3X Quick Start Manual preview
T3X
Brand: G&G Pages: 2
RAPID REBOOT GENESIS Start Manual preview
GENESIS
Brand: RAPID REBOOT Pages: 18
MacDon M1240 Unloading And Assembly Instructions preview
M1240
Brand: MacDon Pages: 170
MacDon D1X Series Assembly Instructions Manual preview
D1X Series
Brand: MacDon Pages: 108
MacDon D1X Series Unloading And Assembly Instructions preview
D1X Series
Brand: MacDon Pages: 108
MacDon R80 Unloading And Assembly Instructions preview
R80
Brand: MacDon Pages: 51
MacDon R80 Operator'S Manual preview
R80
Brand: MacDon Pages: 104
MacDon A40-D Operator'S Manual preview
A40-D
Brand: MacDon Pages: 240
Macherey-Nagel QUANTOFIX Relax Manual preview
QUANTOFIX Relax
Brand: Macherey-Nagel Pages: 192
MacDon A30-D Operator'S Manual preview
A30-D
Brand: MacDon Pages: 182
MacDon A30-S Operator'S Manual preview
A30-S
Brand: MacDon Pages: 192

Brands by name

Popular brands

Load more brands